From: "Mike Duke" To: Cc: Subject: wouxun2 Date: Thursday, June 24, 2010 9:38 AM Setting Receiving CTCSS (R-CTCSS) --- MENU 15 Setting CTCSS/DCS can ignore the unwanted signals from other members working with the same frequency. Only with the same CTCSS/DCS codes can communicate. In Frequency mode, press ? + a M) , the screen displays P-CTC 6 OFF Press (= to enter, it shows 'OFF', press (M / 0 to turn OFF this function or select 67.0Hz to 254.1 Hz CTCSS code, then press ? to confirm, press ? return to standby. >> This transceiver has 50 groups CTCSS, see appendix (1) CTCSS frequency sheet. Setting Transmitting CTCSS (T-CTCSS) --- MENU 16 In standby, press ? + W M , the screen displays T-CT-FF Press ? to enter, it shows 'OFF', press O / 0 to turn OFF this function or select 67.0Hz to 254.1 Hz CTCSS code, then press ? to confirm, press ? return to standby. >> This transceiver has 50 groups CTCSS, see appendix (1) CTCSS frequency sheet. 22 Setting Receiving DCS (R-DCS) --- MENU 17 In Frequency mode, press ? + W W , the screen displays ? Ft-DCS IFF Press ? to enter, it shows 'OFF', press 0 / 0 to turn OFF this function or select D023N to D7541 DCS code, then press ? to confirm, press ? return to standby. This transceiver has 105 groups DCS, see appendix (2) DCS frequency sheet. In it DXXXN (between D023N to D754N) means Positive code while DXXXI (between D0231 and D754I) means Negative code. Setting Transmitting DCS (T-DCS) --- MENU 18 In Standby mode, press ? + M do , the screen displays Press ? to enter, it shows 'OFF', press 0 / 0 to turn OFF this function or select D023N to D7541 DCS code, then press ? to confirm, press ? return to standby. >> This transceiver has 105 groups DCS, see appendix (2) DCS frequency >> sheet. In it DXXXN (between D023N to D754N) means Positive code while >> DXXXI (between D0231 and D7541) means Negative code. 23 Hol Setting Scan Mode (SC-REV) --- MENU 19 This transceiver has three scan modes: TO: When receiving signals, it will go on scanning without any operation within 5 seconds. CO: It will stop scanning when receiving signals, while go on scanning after signal disappeared 3 seconds. SE: When receiving signals it will stop scanning. In Standby mode, press ? + IM M) , the screen displays sc-F;.. TCI Press ? to enter, it shows 'TO', press 0 / ? to select TO/CO/SE scan mode, then press confirm, press ? return to standby. Setting Scan / Lamp / SOS-CH / Radio Function on Side key 1 (PF1) --- MENU 20 There are four functions available on the side key 1 of this transceiver: SCAN: Scan function LAMP: Lamp function SOS-CH: SOS function RADIO: FM radio function OFF: Turn off functions 1. Scan function: In standby mode, press Side key 1 enter to Scan mode (scan mode can be set through MENU 19 Mode Setting), press any key to stop scanning. 24 to -Scan In Standby mode, press ? + W O , the screen displays .FF1 2^ RHC,Ii, Press ? to enter, press 0 / 110 to select SCAN, then press ? to confirm, press ? return to standby. 2. LAMP function: In standby mode, press Side key 1 to turn on the Lamp, press again to turn off. In Standby mode, press ? + 0 0 , the screen displays .FF1 20 . RHGIG Press ? to enter, press 0 / 0 to select LAMP, then press ? to confirm, press ? return to standby. 3. SOS-CH (SOS function): In emergency, it can transmit the "wu...wu..." SOS signals to the outside through the appointed Channel or Frequency in Band A or Band B, meanwhile, the transceiver will sound "wu...wu.-." and the light flashes. It will transmit signals every 5 minutes, lasting for 10 seconds each time. When transmitting SOS signal, press any key to exit. On the interval of transmitting, if carrier signal appears, it starts receiving, after the carrier signal disappears, the transceiver will go on transmitting SOS-CH (SOS function). Press any key to exit. 25 >> In case that SOS-CH frequency you set is not the master frequency. When >> enters SOS alarm function, the transceiver automatically set SOS-CH on >> the master frequency, and will not resume. >> Please press m key to reset the master frequency. In standby, press ? + M U, then screen displays [.FFI - "-~ FFtDIO then press ? to enter, press 0 / 0 to choose SOS-CH submenu, the screen displays MFF,- N H press ? again to confirm, press ? / ? to choose Band A or Band B, then press ? to confirm, the transceiver sounds "wu...wu-.-" , meanwhile the RED/GREEN/FLASHLIGHT flashing, it means set SOS-CH function ON. Through the above setting, in standby, press PF1 side key, to transmit SOS signal. 4. RADIO function: .Turn on the Radio: In standby mode, press Side key 1 to turn on. The screen displays it will search the radio stations automatically when the green light flashing, and will stop until searched. You can listen the radio. ,Tune the radio stations: In Radio mode, press= , the radio will tune the stations automatically and the green light flashing at the same time, it will stop tuning while searched the station. You can also press 0 / 0 to turn the radio stations. 26 *Store the radio stations: When searching the station, press ?, the screen displays F-;_,_7 " c , then you can input any number key between M1 and . The station will be store ~ intd o the transceiver's chip, you can listen this station next time. The transceiver has two groups radio-channels storable. When storing, the default is on the 1St group storage. E.g. if you want to store 88.1MHz into the 1st group Channel 8, just press ? + . If you want to store this frequency into the 2nd group Channel 8, firstly, you should select the 2nd storage, press m, the screen displays ~TEAtZ..c , then switch to the 2nd storage, then press ?+ 90 to store into the 2nd group Channel 8. For the stored station, under the Radio mode, press number key 1 to 9 to listen it. Use m to select the stored stations in 1St and 2nd storage. ? Exit the Radio: Press Side key 1 again to exit the radio mode. When you are listening to the radio, the current frequency or channel still working. Once received signals it will return to the transceiver communicating. After signals disappeared 5 seconds return to Radio mode. When you are listening to the radio, press ? to check the standby frequency.Press PTT to transmit,5 seconds later it will return to the Radio mode automatically. 27 Working Mode (CH-MDF) --- MENU 21 This transceiver has two working modes available: 1. Frequency mode (FREQ) 2. Channel mode Three kinds of channel mode available: lTChannel (CH) T Frequency + Channel number (CH FREQ) 30Channel name (NAME) >> Only input the shift password can change Frequency mode into Channel >> mode, while change among the three kinds of channel mode without >> inputting password. >> To set the shift password via KG-UVD1 programming software. >> Set the password with six "0" is invalid (turn off the Shift password >> function) while set not full of "0" is valid. Frequency (FREQ) and Channel mode changeable OO Invalid password In standby, press ? + m then press 0 / to choose working mode press ? to confirm. 28 O Valid password in standby, press go + go m , then press O / 0 to choose working mode press ? to confirm, the screen displays six short line Input the password, the transceiver shift to the selective mode. >> Channel mode and channel name mode can shift only after stored at least >> one channel and one named channel Setting Auto Backlight (ABR) --- MENU 22 In standby, press ? + g ?M , the screen displays ON Press ? to enter, it shows 'ON', press 0 / 0 to select ON/OFF auto backlight function, then press to confirm, press ? return to standby. >> When the function sets "ON" for opening the auto backlight, it means >> only when you press the number key, the backlight is opened. The >> backlight is closed when transmitting or receiving. >> Shortcut Switch on Frequency Mode and Pure Channel Mode In standby, press 09 + J0 key to switch the mode. Without password, you can switch it directly. Otherwise, you have to input the password firstly. 29 Setting Offset Frequency (OFF-SET) --- MENU 23 Offset frequency means the difference between Tx and Rx frequency. This transceiver's offset frequency range is between 0 to 69.950MHz. In standby mode, press (W + W a) , the screen displays L17,ri O FF 'L Press ? to enter, then press O / 0 to select offset frequency or input the offset frequency through key pad directly press ? to confirm, press ? return to standby. Setting frequency shift direction and offset frequency only in Frequency mode, as for receiving and transmitting in different frequencies. Operating steps: 1. Set the working frequency 2. Set the frequency shift direction and offset frequency. E.g.: In frequency mode, the transceiver needs to work on receiving frequency 450.025MHz and transmitting frequency 460.026MHz In Frequency mode, input dD = 0 0 W M then press ? + do + m + ? to select positive direction (+), press ? +?, then press ? + 0 + ? + ? + 0 / 0 choose 10.000+ ? + ? , the frequency shift direction and offset frequency set. to 30 The screen displays press PTT to transmit and the screen displays Release PTT the screen displays it means receiving frequency is and transmitting frequency is Setting Frequency Shift Direction (SFT-D) ---- MENU24 Shift direction means that: 1. The transmit frequency is higher than receive frequency. This is called positive offset (+). 2. The transmit frequency is lower than receive frequency. This is called negative offset (-). 3. Turn off frequency shift In standby mode, press ? + W m , the screen displays FFT-G? .2v FS~ oFF Press ? to enter, press 0 / 0 to select +/-/OFF, then press ? to confirm, press ? return to standby. 31 Setting Stopwatch Timer (SECOND) --- MENU 25 In standby mode, press ? + 0 M) , the screen displays SE i_ CT 4D . A I OFF Press ? to enter, it shows 'OFF', then press 0 / 0 to turn ON/OFF this function, press =to confirm, press ? return to standby. Using the stopwatch timer: When this function is ON, press m to start counting, while press any key to stop. Press m again to start counting. >> Stop counting, press any key (except m key) to exit stopwatch timer function. Channel Name Edit (CHNAME) --- MENU 26 Edit Channel name: 1. Channel name should be within 26 letters (A to Z) and 10 numbers (0 to 9). 2. Channel name should be less than six length. 3. When selecting (-) means the bit is blank. 32 Edit method: 1. Via programming software. 2. Via keypad of transceiver. Editing: 1. At least one channel should have been stored. 2. The transceiver should be in Channel mode. 3. Enter channel name edit, press 0 to select character while press 0 to select edit position. Edit step: 1. Firstly please set the work mode as NAME display way. 2. Select the desired edit channel, press ? + do + W + ? , the screen displays six '-' symbols, press 0 to select characters and press 0 , then press 0 again to select the second characters, after selecting the sixth character press ? to confirm, press ? to exit. The screen displays the channel name and also the channel number on top right corner. 33 Setting Memory Channels Setting Co-Channel and Dis-Channel (MEM-CH) --- MENU 27 In Frequency mode and in standby, you can input the desired storing frequencies and each parameter. press ? + W W , the screen displays r9Ew-CH z cH-E, ii i Press ? to enter, press 0 / 0 to select channel, then press W to store, a voice prompt means receiving stored. Press ? to exit, the current channel is co-channel. If you need to store dis-channel, repeat the above operation, another voice prompt means sounds - transmitting stored. E.g.: setting 450.025MHz as receiving frequency and 460.025MHz as transmitting frequency which stored in CH-20, then set as following: 1. In Frequency mode, input Cp m 0 0 + ? + + ?, then press 0 or 0 / 0 to select CH-20, press (W to confirm, voice prompt means receiving stored, then press 2. Input W W 0 0 ~ stored, then press ? . 3. The dis-channel is stored. + ? + W W + ? + ?, voice prompt means transmitting 34 >> If the stored channels need to set the CTCSS/DCS codes, you should set >> it before you stored, in case to stored into channel with frequency. >> Transmitting store only can store transmit frequency. >> Manual store, in frequency mode, only desired storing channel is empty >> can set receiving and transmitting store,or only can set transmitting >> store. If the channel had been edited, it can set receiving and >> transmitting store only after deleting the channel. >> Besides manual store, via programming software can also set the >> functions and parameters. Deleting Channel (DEL-CH) ------ MENU 28 In standby mode, press ? + W go , the screen displays ?C?EL-CH 28 CH-001 Press ? to enter, and press 0 / 0 to select the desired deleted channel,then press ? to confirm, the selected channel and message are deleted, press ? return to standby. 35 Setting Reset ---- MENU 29 This transceiver has two resets available - VFO and ALL messages. When you use RESET VFO, all function parameters will return to default set. When you use RESET ALL, the transceiver's all settings return to default set. 1. MENU Reset (VFO): In standby mode, press ? + , the screen displays .RESET VFn Press ? to enter, and press 0 / 0 to select VFO, then press ?,the screen displays F'E-ET SOURE'? press go again to confirm, and the screen displays ~RE F~l FIT . After set Reset, the transceiver will auto power off and reboot again. 2. All messages Reset (ALL) To avoid disoperation, you can set the password of ALL messages Reset (ALL) for this transceiver through Programming software. All messages reset will only work after the right password is input. Pls see the Programming software for the setting of password, 6 figures, while setting "000000" means cancelling the password lock function. (1). Setting password as "000000" In standby, press ? + M M) , the screen displays .RESET X29 REE 36 Press ? to enter, and press 0 / to select ALL, press ?, the screen displays ~RE,FE-.zg , then press go again to confirm, the screen displays ~E~~~a i r when the reset is finished, the transceiver will automatically turns off and reboot again. (2). Setting password as "XXXXXX" (E.g.: 123456) ~F:ESET In standby, press ? + the screen displays 2g FILL Press ? to enter, and press 0 / 0 to select ALL, press go , the screen will displays 'PESET zs at this time input the six figure password (e.g.: 123456), the screen displays '~'E NFL' the transceiver will start resetting. After reset is finished, transceiver will automatically turns off and restart. 37 r7ow ro opera.e %k M CTCDDIDCS Frequency Scan ------ MENU 30 This function is to scan all CTCSS or DCS frequencies to confirm if the transmitting party has the CTCSS or DCS frequencies to transmit. When CTCSS or DCS frequencies are not matched between you and other members in the same group, you can use this function to confirm CTCSS or DCS frequencies. When the transceiver is in receiving, presss ? + a) U , the screen displays . SCN Press ? to enter, the arrowhead points to CTCSS". Press (2 / 0 select to scan CTCSS or DCS. And then press ? to confirm, it starts scanning CTCSS/DCS frequencies. >> This function can not work under the channel mode. >> The function can >> not start up without detecting signals. >> Press 0 / 0 or turn code switch to reverse the scanning direction. >> When identifying CTCSS or DCS frequencies, the identified frequency >> will display on screen. In this moment, you can press ? instead of >> present CTCS or DCS frequencies temporarily. If you need direct >> replacement, please enter CTCSS menu (Menu 15 & Menu 16) or DCS menu >> (Menu 17& Menu 18) to save and confirm. Otherwise, the value will come >> back to the prior one after restoration. >> Only when the band that the arrowhead points receives signal, the >> transceiver can enter CTCSS/DCS frequency to scan. 38 DTMF Encoding ?, QM, 0 , ? are corresponding to A, B, C, D on DTMF Please follow the below steps to dial up manually: 1. Press PTT key to transmit. 1 2. In the meantime of transmission, press the key, and the corresponding DTMF tone is sent out. The transceiver transmits the corresponding tone, which can be monitored by the speaker. ANI ID Code Edit, ANI ID Code Transmit, ANI ID Code Transmit Delay and Setting DTMF Sidetone >> The above functions in this transceiver only can be edited by our >> programming software. AN] ID Code Edit ANI ID Code can be edited by 6 digits, which is made up of A, B, C, D and 0-9. ANI ID Code Transmit 39 Switch of ANI ID Code Transmit means that when you are communicating, press [PTT] key every time, the ANI ID CODE will be auto or manual transmitted. Selecting ON means automatically transmit, OFF means manually transmit. ANI ID Code Transmit Delay ANI ID Code Transmit Delay means when you are communicating, press [PTT] key every time to delay transmit ANI ID Code automatically. The longest time of ANI ID Code auto transmit delay is 3seconds, which is divided into 30 levels and 100ms per level. Setting DTMF Sidetone DTMF sidetone gives you the opportunity to switch on or off the speaker and hear the relative DTMF tone when transmit DTMF There are 4 options on setting sidetone: O Key Tone: In transmitting, press number key to open the sidetone. O ANI ID Code Transmit Sidetone: Opening sidetone when the transceiver transmits ANI ID code. O Key tone + ANI ID Code Transmit Sidetone: In transmitting, opening side tone by number key or during transmitting ANI ID code. ? Turn off Sidetone: In encoding, all sidetone turns off. 40 Setting Priority Scan Function If you want to monitor the other frequency and check the certain preferred frequency at the same time, you can set Priority scan function. E.g.: Scan six channels: CH1, CH2, CH3, CH4 and CH5 as the common scanned channel, and CH6 set as the priority scanned channel. Scanning sequence as following chart: CH~ 1- CH6 - CH2 ~ CH6 ~ CH3 ~ CH6 CH4 ~ CH6 CH5 , CH6 If the transceiver checks the signal on "Priority Channel", it will call out its frequency. Select the priority channels via programming software. Setting Reverse Frequency Function When using reverse frequency function, the transmitting and receiving frequency of transceiver will interchange, and the CTCSS and DCS encode and decode will interchange either. Operating reverse frequency function: In standby mode, press ? to turn on the reverse frequency function; press do again to turn off. In Frequency Mode: 1. If the menu setting turns on 41 2. If your transceiver permits reset The editing method of the above two functions: via software Low-voltage Battery Voice Prompt When the battery pack has low voltage, the transceiver will sound "low battery pack", and the LED will flash every 5 seconds and a "click" sounds. Transmit Overtime Prompt When transceiver transmits beyond the limited time, there will be a sound warning "transmit overtime", and stop transmitting. Press PTT to transmit again. (Setting Transmit Over Timer pls see page 16) Adding Scanning Channel >> Channel scan only according to scan list which had been added. >> Edit >> method: Strictly via programming software. 42 Switch sourceradio on, after you have LED is flashing red during cloning. connected the targetradio to the sourceradio LED goes out in case of successful cloning. via the cloningcable, push the [MONI] key LED glows continuous red in case of cloning Using wireclone and the sourceradio starts cloning.- failure- _- - LED is flashing green during cloning. Targetradio LED will switch OFF when cloning complete, to choose band A, set the Tx frequency and sub-tones which need to work with the Working with Repeater This transceiver has two working modes while working with repeater. OFrequency mode working with repeater OChannel mode working with repeater 1. Frequency mode working with repeater O Press repeater. OPress m to choose band B, set the Rx frequency (if the repeater has TX sub-tones, you can also set sub-tones in band B). OPress ? + M , frequency mode working with repeater set. The TDR disappeared but the screen displays " 8 ". And then press m again, the setting is finished. 43 2. Channel mode working with repeater T Edit the Tx & Rx frequency and sub-tones on the channel which need to work with repeater. 0O In channel mode, and call out the above edited channel, press m to set this channel as the current one. How to Use the Intelligent Charger 1. Insert the AC plug into the outlet (AC: 90-240V), the charger indicator flashes, it means enter charging standby . 2. Insert the battery into the charger, the RED indicator turns on, it means charging, while GREEN indicator turns on, it means fully charged. >> When insert the exhausted battery pack into the charger, it pre-charger >> the battery pack in trickling charge, meanwhile, the RED light flashing >> and lasts 10 to 20 minutes, then enter normally charging with RED light >> on, it will turn to GREEN when fully charged. >> Tricking charge the exhausted battery pack in case to protect the >> Li-ion battery. 44 Trouble shooting Please check carefully if your transceiver has problems by following this chart. If you maintain to have trouble you can reset your transceiver and very often this will eliminate your problem. Problem Solution Cannot power on, 1. The battery may exhausted, pls change the new battery or re-charge. no power 2. The battery install incorrect, pls take out the battery and re-install. 1. The battery life is over, pls change a new battery. Battery life not long 2. Not charging completely, be make sure fully charged before take out. Receive light turn on but 1. Make sure the volume is highest no sounds 2. Make sure the CTCSS/DCS code is the same with other members. 1. Make sure the keypad is locked or not. Keypad do not work 2. Make sure any other key stuck. In standby, it will auto- Make sure VOX function is ON or not, and its level is set too transmit without pressing PTT low or not. 45 ell Problem Solution Some functions can not Make sure work in Channel mode. Some functions can be set only via be stored programming software in Channel mode. Receive other groups signal Pls change another CTCSS/DCS code of your group. while communicating 46 Technology parameter CTCSS Appendix 1 1 67.0 11 94.8 21 131.8 31 171.3 41 203.5 22 69.3 12 97.4 22 136.5 32 173.8 42 206,5 33 7 1 9 13 100.0 23 141.3 33 177.3 43 210.7 71.9 4 74.4 14 103.5 24 146.2 34 179.9 44 218.1 5 77.0 15 107.2 25 151.4 35 183.5 45 225.7 6 79.7 16 110.9 26 156.7 36 186.2 46 229.1 7 82.5 17 114.8 27 159.8 37 189.9 47 233.6 8 85.4 18 118.8 28 162.2 38 192.8 48 241.8 9 88.5 19 123.0 29 165.5 39 196.6 49 250.3 10 91.5 I 20 I 127.3 30 167.9 40 199.5 50 254.1 47 -- Mike Duke, K5XU Email services provided by the System Access Mobile Network. Visit www.serotek.com to learn more about accessibility anywhere.